Showroom Location:
23701 Halsted Road
Farmington Hills, MI 48335
Ask an Expert
Angie's List
Two Year Warranty
Liftmaster Garage Door Openers

 

Stanley Keyless Entry System Instructions

 

Does your Stanley Keyless Entry pad say "Secure Code" anywhere on the front of the pad? If yes, move on to #2 Instructions. If no, Go to #1 Instructions

 

Does your Motor Unit (the part hanging from the ceiling of your garage) have a LEARN/TEACH button on the back? If yes, Go to #2 Instructions. If no, go to #3 Instructions

 

#1 Instructions (Non Secure Code Keyless Entry system with Dipswitch Opener)

 

STEP 1: determine the code from your transmitter (remote control) or motor
• You'll find a small circuit board inside your transmitter with 10 dipswitches (rocker switches). The code is represented by the numbers that have the switch pushed toward the numbers or flush with the numbers. (Dipswitch #10 is the number 0 on the keyless entry pad). For instance, if the second, fourth, seventh and tenth switches are pointing toward the numbers, your code is 2470.
• If you do not have a transmitter, you can find the same set of dipswitches on the back of your motor unit (the part hanging from the ceiling of your garage) to the right of the power cord.    

 

STEP 2: clear all old programming on your keyless entry pad
• Take the battery out of your keyless entry pad. With the battery out, press any three buttons to release any stored memory. Put the battery back in & wait until the light behind the numbers on the keyless entry pad goes out (about 30 seconds).
• Press the RADIO LEARN button 2 times
• Press buttons 1, 2, 3, 4
• Enter the code from the transmitter or motor (see step 1)
• Press the RADIO LEARN button once and wait until the light behind the numbers on the keyless entry pad goes out (about 30 seconds)        

 

 

STEP 3: program the PIN number of your choice
• Press the ACCESS LEARN button 2 times
• Press buttons 1, 2, 3, 4 (this is the default setting set by the factory)
• Enter your 4 digit PIN number
• Press the ACCESS LEARN button once and wait until the light behind the numbers on the keyless entry pad goes out (about 30 seconds)
• Your keyless entry pad is now programmed with your PIN number          

 

STEP 4: • Program your Stanley garage door opener
• Press the LEARN/TEACH button on back of motor unit (the part hanging from the ceiling of your garage). The LED light above the LEARN/TEACH button will flash.
• Press & hold the HOMELINK button on car and wait until the light on the Homelink system blinks fast

 

• Program your Stanley garage door opener • Press the LEARN/TEACH button on back of motor unit (the part hanging from the ceiling of your garage). The LED light above the LEARN/TEACH button will flash. • Press & hold the HOMELINK button on car and wait until the light on the Homelink system blinks fast

 

 

#2 Instructions (Secure Code Keyless entry pad with Secure Code Opener)

 

STEP 1: clear all old programming on your keyless entry pad

 

• Press & hold the RADIO LEARN and the ACCESS LEARN button at the same time. Hold for approximately 10 seconds, until the light next to the word “Stanley” on the keyless entry pad goes out.
• Press the LEARN/TEACH button on the back of the Motor Unit (the part hanging from the ceiling of your garage)
• Go back to the keyless entry pad and press buttons 1, 2, 3, 4. Wait until the light next to the word “Stanley” on the keyless entry pad goes out. Now your keyless entry pad is programmed with PIN number 1234.      

 

STEP 2: program the PIN number of your choice
• Press the ACCESS LEARN button 2 times. Make sure all the lights on the keyless entry pad are out.
• Press buttons 1, 2, 3, 4
• Enter your 4 digit PIN number
• Press the ACCESS LEARN button once
• Wait until the light next to the word “Stanley” on the keyless entry pad goes out. Your keyless entry pad is now programmed with your PIN number.  

 

    

#3 Instructions (Secure Code Keyless entry pad with Dipswitch Opener)

 

STEP 1: determine the code from your transmitter (remote control) or motor
• You'll find a small circuit board inside your transmitter with 10 dipswitches (rockers). The code is represented by the numbers that have the switch pushed toward the numbers. (Dipswitch #10 is the number 0 on the keyless entry pad). For instance, if the second, fourth, seventh and tenth switches are pointing toward the numbers, your code is 2470.
• If you do not have a transmitter you can find the same set of dipswitches on the back of your motor unit (the part hanging from the ceiling of your garage) to the right of the power cord      

 

STEP 2: clear all old programming on your keyless entry pad
• Press & hold the RADIO LEARN and the ACCESS LEARN button at the same time. Hold for approximately 10 seconds, until the light next to the word “Stanley” goes out.
• Press the RADIO LEARN button 2 times
• Enter the code from the transmitter or motor (see step 1)
• Press the RADIO LEARN button once and wait until the light next to the word “Stanley” goes out (about 30 seconds)      

 

STEP 3: program the PIN number of your choice
• Press the ACCESS LEARN button 2 times
• Press buttons 1, 2, 3, 4 (this is the default setting set by the factory)
• Enter your 4 digit PIN number
• Press the ACCESS LEARN button once and wait until the light next to the word “Stanley” goes out (about 30 seconds)
• Your keyless entry pad is now programmed with your PIN number

Copyright © 2018. All Rights Reserved.